Revenge from Mars monitor problem

I am waiting for the postman..............nothing until this time
regards
Winfried
 
Arrived today, i will have a look on it
But i nowhere can read your sending-addy......
Send me your adress via PN
regards
Winfried
 
THX.
Your Chassis ist definitly faulty, the power-supply is dead.
There is an integrated circuit, that does the switching job, i think, that is defective.
I will order this part..... and then we know more about this.
Regards
Winfried
 
Oké, good that you found the problem.
Maybe it is a good idea when you find parts from withs you know will break down easy when a board gets old and the price for these parts is not that high to changes these parts aswell to make the board more future proof.
 
I have to examine the cause of the breakdown. Dont want to kill the new ic, i ordered it today in the city that never sleeps... 0-).... HK
May take few weeks until it arrives, but i ordered in foresight five pieces! One for the rep, the second, if i make any mistake and the rest for my storage!
Found a totally bad capacitor at the sense-line of the switchmode-ic. And a broken transistor in the startup-circuit.
i will try to repair the periphery round this ic.
And in the meantime your signal connection cable will get a suitable plug. Its not good style to solder such a cable directly at the pins of the pcb.
Sorry for the delay, but i only will do a good job at really fair price.
Regards
Winfried
 
Surprise!
It works. The ic is in good condition, the periphery was faulty, only. I replaced the startup transistor and the power supply fired up!
The second fault was a strange moiree in the picture, there was a ripple on the 12V rail. The belonging Cap was bad, after change the picture was good.
After half a hour test run the contrast flickered and introduced me to a new problem. Arghhhh, why i have everytime the same blues with different faults at the same set!?!
Also i fixed it by soldering the video-processor-ic. it was sensitiv to vibration.
Now it runs since above two hours, tomorrow i will pack it and send it on the way back.
The signal cable is also repaired.
Appendix: Pics



jpg.gif
jpg.gif
jpg.gif
jpg.gif
 

Anhänge

  • Anschluß-1.jpg
    Anschluß-1.jpg
    141.8 KB · Aufrufe: 19
  • Anschluß-2.jpg
    Anschluß-2.jpg
    111.5 KB · Aufrufe: 20
  • busy-1.jpg
    busy-1.jpg
    143.4 KB · Aufrufe: 21
  • busy-2.jpg
    busy-2.jpg
    155.4 KB · Aufrufe: 21
Und überhaupt, wassn hier wieder los?
Die scheiß Bilder anzuhängen hat mich ja fast wahnsinnig gemacht......bin ich zu blöd? neee, eigentlich nicht
Warum kann das nicht so einfach sein wie.......und es ist natürlich nicht so, wie ich es gerne hätte....FUCK
und jetzt mache ich mir Essen und rege mich ab

@firedragon:
Thats not your fault, im pissed off about handling the pics here

N8@all
 
Geht doch! Und die IC sind bestellt :cool:
Jetzt bekomme ich halt wieder ein paar Bauteile mehr............ich kann es nicht ab, wenn ich sowas nicht in der Schublade habe

@firedragon:
The paket is on the way back to you, perhaps it will arrive until SA
I hope, that your tube works.
Regards
Winfried
 
!!!! Awesome !!!!
all the things you repaired I could have never done myself heck some parts I don't even know what they are :confused: good thing there are specialists.
let me know what I ow you and send me your bank number so I can pay you.
really hope the tube is still good.
thank you, thank you, thank you !!! for now. :)
i will keep you informed about the progress
 
HI
When you will get the Chassis, have a look at the liitle push-switch on the pcb in the near of the signal-connector.
It has a black knob and switches the polarity of the sync. In case of no sync or bad sync switch it in the other position.
The Pin2000 has another polarity of sync as the normal arcade-pcbs, also my pic-generator, due to the fact, that here works a modified computer-graphic-chip.
With VGA-standards, thats also the reason, why there is seperate sync H + V. I cannot remind, wether i switched it back or leaved it in the wrong position.
Naturally you also have to set the controls at the side of the line-out-transformer, screen and sharpness first after firing up.
Then the fine tuning, if necessary. The basic settings are done, you may have to adjust the gray and white balance on the neckboard.
Also the geometry. Hor. width ist the only pot in the near of the transformer, i think, its lettered.
All other pots are on the adjusting-pcb. Before you roll over everywhere tuned, ask me!
Good luck!
Regards
Winfried
 
Oké great.
i will transfer the money tomorrow.
fingerscrossed it will work.
i will only chance the settings you told me.
you will hear from me soon when I got everything installed.
 
Hi Winfried,
i put the boards back in just to be save I checked 3 times if I connected everything right and if I not forget anything coos I not want to do it wrong and break stuff coos I did an stupid thing.
than moment of truth.
i turned the machine on.
i heard the monitor turn on but only a black screen.
i started to stress a little.
turned the machine of switched the switch you told me about.
turned the machine on again but still a black screen.
omg now I'm was getting really nervous.
then I turned a little on the buttons of the big black thing.
than YAY picture omg big big smile :)
so happy right Now.
Thank you, thank you, thank you !!!!!
if you ever in the neighborhood (I live near Rotterdam) and you feel like playing some pinball or just a cup of coffee or something your just let me know your more than welcome.
i will put on some pics when I got it all build in.
 
My best wishes cause your CRT is working fine too............the chassis was not the really prob :p
ENJOY! ENJOY! ENJOY!
And i am very happy for saving an old monitor from the scrap!
This is my core business.......they recommend me further
Regards
Winfried
 
Zurück
Oben